Previous Page. Next Page. Multi-use loudspeaker all-weather 80 mm 3. All-weather mm 5. Ad-c series mm 8" 2-way coax baffle assembly pre-install enclosure for ad-c mm 8" 2-way coax blind-mount split ring and tile rails for ad-c round grille for 8" loudspeaker square grille for 8" loudspeaker mm 12" 2-way coax baffle a 24 pages.
Page 3 The AD-S82 loudspeaker systems are full range, high output, two-way designs delivering superior sound quality and high SPL in a lightweight, all-weather enclosure.
These loudspeakers make an excellent choice for a wide variety of SR applications. Page 4 Mounting If using the loudspeaker only no optional mount , the loudspeaker can be set on any appropriate surface. The cabinet will lean back at a slight angle when set on a flat surface. When operated at high output levels, the cabinet can generate sufficient vibration, causing the cabinet to move or creep if set on a hard surface.
Make sure the tapered side of the gasket is toward the cover. Push the gasket into its seat, and thread the nut over the speaker wire and tighten. If using the YM-8, connect the wires directly to the binding posts.
Page 12 Painting the AD-S82 H Loudspeaker The loudspeaker enclosure and grill can be painted to match any decor, provided the following precautions are observed. This limited warranty is freely transferable during the term of the warranty period. In the event that this product was manufactured for export and sale outside of the United States or its territories, then this limited warranty shall not apply.
Removal of the serial number on this product, or purchase of this product from an unauthorized dealer, will void this limited warranty. Periodically, this warranty is updated. Patent and Trademark Office All trademarks are the property of their respective owners. These products represent the state-of-the-art in all-weather, lightweight SR sound reinforcement loudspeaker systems.
To get the most from your investment, we encourage you to review this manual carefully. The AD-S82 loudspeaker systems are full range, high output, two-way designs delivering superior sound quality and high SPL in a lightweight, all-weather enclosure. These loudspeakers make an excellent choice for a wide variety of SR applications.
Before mounting the loudspeaker, determine the mounting orientation and desired coverage angles. The waveguide can be rotated to interchange the coverage angles. Gently and evenly work the grill out of its retaining groove to avoid bending the grill. A 2-size Phillips screwdriver is recommended. Be careful not to damage the connections, wiring, or the gasket between the waveguide and the cabinet. Make certain the wiring is not stressed or pulled loose from its connections when rotating the assembly.
Reposition it, if required. Set the waveguide in place and install the screws. Do not overtighten. If using optional ID-8 or YM-8 mounting hardware, refer to the instructions provided with the hardware. Maintain proper speaker and amplifier connection polarity throughout the entire system. All positive-marked loudspeaker terminals should be connected to positive-marked amplifier output terminals. This will provide the best possible low-frequency output from your system.
If using the loudspeaker only no optional mount , the loudspeaker can be set on any appropriate surface. The cabinet will lean back at a slight angle when set on a flat surface. When operated at high output levels, the cabinet can generate sufficient vibration, causing the cabinet to move or creep if set on a hard surface. Use anti-slip matting under the cabinet or self-adhesive rubber feet to keep the cabinet from creeping.
On the back of the loudspeaker, near the bottom, is a safety cable attachment point. Install a safety cable strong enough to support several times the weight of the loudspeaker assembly in the event it may fall. Ensure the mounting surface and supporting structure are appropriately strong enough to support the loudspeaker assembly and any potential vibration or seismic activity. Attach a safety cable to the attachment point on the bottom-back of the loudspeaker. Ensure the safety.
This mount allows for all mounts and wiring to be fully installed and the loudspeakers to be placed at the last possible moment. A security retaining screw for the latch in included, making speaker removal impossible without the correct Allen hex bit to remove the screw.
The IntelliDock mount and its wiring feed-through bushing provide maximum weather resistance and maximum acoustic coverage range adjustment. The ID-8T is identical to the ID-8, but equipped with an audio matching transformer with 70V and V distributed audio input capability.
The adapter plate can be removed if desired, however, we recommend its use. Secure the cover to the ball-mount assembly.
The more detail you provide for your issue and question, the easier it will be for other QSC AD-S82 owners to properly answer your question. This manual comes under the category Speakers and has been rated by 1 people with an average of a 7. This manual is available in the following languages: English. Is your question not listed? Manual del Usario.
Ask a question. Related product manuals.
0コメント